Abstract
The article is devoted to studying the influence of wire feed rate on the hardness of the welded layer during the restoration of electric motor shafts. The authors analyze the importance of optimal hardness to ensure the durability and reliability of the reconditioned parts. The paper considers various factors affecting the hardness of the welded layer, such as type of welding wire (AWS A5.18 ER70S-6, OK Tubrodur 35 G M, AWS A5.28 ER80S-G); cladding modes (feed rate, current, voltage); properties of the welded clad metal (fusion with the base, tendency to crack formation). Based on the conducted experiments, the optimal welding modes for each of the studied wires and the corresponding hardness values were determined. The obtained results allow us to conclude that the wire feed rate is one of the key parameters affecting the hardness of the welded layer.
Keywords
References
Pradeep, G. R. C., Ramesh, A., & Durga, P. B. (2010). A review paper on hardfacing processes and materials. International Journal of Engineering Science and Technology, 2(11), 6507–6510.
Nurzhanova, O., Zhukova, A., & Bučinskas, V. (2023). Investigation of the performance properties of parts surfaces to be recovered by semiautomatic hardfacing. Trudy Universiteta, (2), 52–58. https://doi.org/10.52209/1609-1825_2023_2_52
Klimpel, A. (2020). Industrial surfacing and hardfacing technology, fundamentals and applications. Welding Technology Review, 91(12), 33–42. https://doi.org/10.26628/wtr.v91i12.1094
Zharkevich, O., Taimanova, G., & Mukhitova, A. (2023). Analysis of shaft defects of electric motors and methods of their restoration. Trudy Universiteta, (4), 3–9. https://doi.org/10.52209/1609-1825_2023_4_3
Olugbade, T. O., Ojo, O. T., Omiyale, B. O., Olutomilola, E. O., & Olorunfemi, B. J. (2021). A review on the corrosion fatigue strength of surface-modified stainless steels. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 43, 421. https://doi.org/10.1007/s40430-021-03148-5
Nurzhanova, O., Zharkevich, O., Bessonov, A., Naboko, Y., Abdugaliyeva, G., Taimanova, G., & Nikonova, T. (2023). Simulation of the distribution of temperature, stresses and deformations during splined shafts hardfacing. Journal of Applied Engineering Science, 21(3), 837–845.
Kikai, N., Ronbunshu, G., & Hen, A. (2007). Destruction phenomenon about the spline shaft. Transactions of the Japan Society of Mechanical Engineers, Part A, 73(725), 80–87. https://doi.org/10.1299/kikaia.73.80
Kenchi, R. K. M. (2012). The effects of welding processes on microstructure and abrasive wear resistance for hardfacing deposits. Bonfring International Journal of Industrial Engineering and Management Science, 2(2), 28–34. https://doi.org/10.9756/BIJIEMS.1298
Garbade, R., & Dhokey, N. (2021). Overview on hardfacing processes, materials and applications. IOP Conference Series: Materials Science and Engineering, 1017, 012033. https://doi.org/10.1088/1757-899X/1017/1/012033
Nashid, H., Ferguson, W. G., Clifton, G. C., Hodgson, M., Battley, M., Seal, C., & Choi, J. H. (2014). Non-destructive method to investigate the hardness–plastic strain relationship in cyclically deformed structural steel elements. Bulletin of the New Zealand Society for Earthquake Engineering, 47(3), 181–189.
Joseph, P., Babu, M. N., & Albert, S. K. (2024). Fracture behavior of hardfacing alloy coated over stainless steel under quasi-static and dynamic loads. Journal of Materials Engineering and Performance, 33(23), 13019–13029. https://doi.org/10.1007/s11665-024-10389-7
Zhang, Y., Sang, X. T., Xu, G., & Wang, G. (2023). Fatigue crack propagation of the gradient surface-modified layer of high-strength steel. International Journal of Fatigue, 177, 107921. https://doi.org/10.1016/j.ijfatigue.2023.107921
Zharkevich, O., Nurzhanova, O., Zhunuspekov, D., Naboko, Y., Buzauova, T., Abdugaliyeva, G., Mateshov, A., & Bessonov, A. (2023). Determination of optimal hardfacing modes for recovering electric motor shafts. Tehnički Vjesnik, 30(3), 951–957. https://doi.org/10.17559/TV-20220719104215
International Organization for Standardization. (2019). ISO 643:2019. Micrographic determination of the apparent grain size.
Zharkevich, O. M., Nurzhanova, O., Bessonov, A., Naboko, Y., Abdugaliyeva, G., Taimanova, G., & Nikonova, T. (2023). Simulation of the distribution of temperature, stresses and deformations during splined shafts hard facing. Journal of Applied Engineering Science, 21(3), 837–845. https://doi.org/10.5937/jaes0-42774
Mussayev, M., Sherov, K., Kassymbabina, D., Abdugaliyeva, G., Donenbayev, B., Kardassinov, S., Karsakova, N., & Tussupova, S. (2024). Research of wear and increasing wear resistance of the working part of busbar punching tools by surfacing method. Journal of Applied Engineering Science, 22(3), 654–664. https://doi.org/10.5937/jaes0-51175
GOST 12080–66. (1966). Kontsy valov tsilindricheskiye.
Zhetesova, G., Zharkevich, O., Pleshakova, Y., Platonova, Y., Yurchenko, V., & Buzauova, T. (2017). Building mathematical model for gas-thermal process of coating evaporation. Metalurgija, 55(1), 63–66.
Bezkorovainyy, P. G., Teliman, I. V., Malybaev, N. S., & Shestakov, V. S. (2023). Hydraulic excavator bucket modeling with a straight shovel along a defined trajectory. Material and Mechanical Engineering Technology, 1(1), 29–33. https://doi.org/10.52209/2706-977X_2023_1_29
- Autori zadržavaju autorska prava i pružaju časopisu pravo prvog objavljivanja rada i licenciraju ga Creative Commons licencom koja omogućava drugima da dele rad uz uslov navođenja autorstva i izvornog objavljivanja u ovom časopisu.
- Autori mogu izraditi zasebne, ugovorne aranžmane za neekskluzivnu distribuciju rada objavljenog u časopisu (npr. postavljanje u institucionalni repozitorijum ili objavljivanje u knjizi), uz navođenje da je rad izvorno objavljen u ovom časopisu.
- Autorima je dozvoljeno i podstiču se da postave objavljeni rad onlajn (npr. u institucionalnom repozitorijumu ili na svojim internet stranicama) pre i tokom postupka prijave priloga, s obzirom da takav postupak može voditi produktivnoj razmeni ideja i ranijoj i većoj citiranosti objavljenog rada (up. Efekat otvorenog pristupa).