Supplementary Files
Abstract
This work demonstrates static testing of a composite blade W55RBVS structure for the wind turbines of up to 6kW power. The testing consists of the static testing of the structure up to the moment of the blade failure. The main purpose of the testing is to define and directly verify the rigidity of the blade W55RBVS, to determine the maximum force which leads to faliure and the relative span of the blade failure. W55RBVS composite blades, manufactured by the company WING.doo and are installed on a two-blades wind turbine Eoltec Scirocco. This test is defined in the standard IEC 61400-2 /8/. Blade testing is performed in the Aerotechnics Laboratory of the Faculty of Mechanical Engineering, Belgrade University. The load test is performed up to the moment of the blade failure. The result of the testing will be used in order to improve the design of the blade W55RBVS.
Keywords
Array
Array
Array
References
C. Mitrovic, N. Petrovic, D. Bekric, A. Bengin, B.Rakicevic “Micro-Structure Characterization of Composite Wind Turbine Blade Following Structural Testing “, Wulfenia Journal,
Vol 21, No. 2; Feb 2014, ISSN: 1561-882X
C. Mitrovic, N. Petrovic, D. Bekric, V.Dragovic, I.Mileusnic, “Characterization of Micro-structures of Composite of Small Wind Turbine Blade following Structural Testing up to Failure “, The 4th International Conference Advanced Composite Materials Engineering COMAT 2012, 18- 20 October 2012, Brasov, Romania.
C. Mitrovic, N. Petrovic, A. Bengin, D. Bekric, V.Dragovic, A.Simonovic, G. Vorotovic, S. Radojevic, D. Stamenkovic, “Structural Testing of Small Wind Turbine Blade up to Failure“, International Conference on Innovative Technologies. Conference IN-TECH 2011,
Bratislava, 2011.
C. Mitrovic, N. Petrovic, D. Bekric, A. Bengin, B.Rakicevic : Micro-Structure Characterization of Composite Wind Turbine Blade Following Structural Testing, International Journal of Engineering & Technology IJET-IJENS Vol:13 No:01
International standard IEC 61400-1, Wind turbines – Part 1: Design requirements, Switzerland.
International standard IEC 61400-2, Wind turbines – Part 2: Design requirements for small wind turbines, Switzerland.
N.Yahya, M.Kashif, H.Daud, H.Mohd Zaid, A.Shafie, N.Nasir, A.See,:Fabrication and Characterization of Y3.0-XLaXFe5O12 PVA Composite as EM Waves Detector, International
Journal of Basic & Applied Sciences IJBAS - IJENS Vol: 9 No: 9, pages 131-134, 2009
Pantelis, B., Konstantinidis, E., Pitsa, D. (2012): „Systemic assessment and analysis of factors affect the reliability of a wind turbine”, Journal of Applied Engineering Science (Istraživanja i projektovanja za privredu), No. 2, Vol. 10, pp. 85-92
Puneet Malhotra “Advanced Blade Testing Methods for Wind Turbines”, University of Massachusetts - Amherst, Masters Theses. Paper 529, 2010
R.Backers, Eoltec Shirocco E5.6-6, Instalation&Maintanence Manual, 2009- 2010, Solacity Inc
- Autori zadržavaju autorska prava i pružaju časopisu pravo prvog objavljivanja rada i licenciraju ga Creative Commons licencom koja omogućava drugima da dele rad uz uslov navođenja autorstva i izvornog objavljivanja u ovom časopisu.
- Autori mogu izraditi zasebne, ugovorne aranžmane za neekskluzivnu distribuciju rada objavljenog u časopisu (npr. postavljanje u institucionalni repozitorijum ili objavljivanje u knjizi), uz navođenje da je rad izvorno objavljen u ovom časopisu.
- Autorima je dozvoljeno i podstiču se da postave objavljeni rad onlajn (npr. u institucionalnom repozitorijumu ili na svojim internet stranicama) pre i tokom postupka prijave priloga, s obzirom da takav postupak može voditi produktivnoj razmeni ideja i ranijoj i većoj citiranosti objavljenog rada (up. Efekat otvorenog pristupa).